RAD Data comm FOM-E3 Especificações Página 93
- Página / 102
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
DC Power Supply Connection – AC/DC Adapter (AD) Plug
Note: Ignore this supplement if the unit is AC-powered.
Certain units are equipped with a Wide Range AC/DC power supply. These units
are equipped with a standard AC-type 3-prong power input connector located on
the unit rear panel. This power input connector can be used for both AC and DC
voltage inputs.
For DC operation, a compatible AC/DC Adapter (AD) plug for attaching to your
DC power supply lines is used (see Figure 1).
Connect the wires of your DC power supply cable to the AD plug, according to the
voltage polarity and assembly instructions provided below.
Caution: Prepare all connections to the AD plug before inserting it into the unit’s
power connector.
Preparing and Connecting the Power
Supply Cable with the AD
Plug
1. Loosen the cover screw on the bottom of the
AD
plug to open it
(see Figure 2).
2. Run your DC power supply cable through the removable cable
guard and through the open cable clamp.
3. Place each DC wire lead into the appropriate
AD
plug wire
terminal according to the voltage polarity mapping shown.
Afterwards, tighten the terminal screws close.
4. Fit the cable guard in its slot and then close the clamp over the
cable. Tighten the clamp screws to secure the cable.
5. Reassemble the two halves of the
AD
plug and tighten the cover
screw.
6. Connect the assembled power supply cable to the unit.
Warning:
• Reversing the wire voltage polarity will not cause damage to the
unit, but the internal protection fuse will not function.
• Always connect a ground (earth) wire to the AD plug’s Chassis
(frame) Ground terminal. Connecting the unit without a protective
ground, or interruption of the grounding (for example, by using an
extension power cord without a grounding conductor) can cause
harm to the unit or to the equipment connected to it!
• The AD adapter is not intended for field wiring.
Figure 1
SUP-930-05/04
Chassis
(frame)
Ground
+
Positive
pole
(Earthed)
Negative
pole
DC power
source
Open
AD plug
(top view)
Bottom
of AD plug
AC/DC power
input connector
on unit
DC power
cable
Wire
terminals
Cable
clamp
(closed)
Cable
guard
48/60VDC~100-240VAC/
RETURN
POWER
Figure 2
- RICi-E3, RICi-T3 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Quick Start Guide 11
- Starting a Terminal Session 12
- Configuring Basic Parameters 13
- Contents 15
- Chapter 1 17
- Introduction 17
- ConfiguRAD 18
- RADview-Lite 18
- RICi-E3, RICi-T3 Ver. 1.0 18
- Inband Management 19
- 1.3 Functional Description 20
- 1.4 Technical Specifications 21
- Chapter 2 23
- Installation and Setup 23
- Figure 2-1 25
- Appendix A 25
- Chapter 3 27
- Operation 27
- Name Color Function 28
- 3.3 Default Settings 29
- Working via ASCII Terminal 32
- Logging In 33
- Selecting Options 33
- Navigating Tables 34
- Working with ConfiguRAD 35
- Working with RADview-Lite 37
- 3.5 Menu Map 38
- 3.6 Turning Off the Unit 39
- Chapter 4 41
- Configuration 41
- Configuring the DHCP Client 42
- Managing IP Parameters 43
- Entering Device Information 44
- Configuring Communities 44
- Figure 4-2 45
- Figure 4-4 45
- Figure 4-5 46
- Figure 4-6 46
- Figure 4-8 50
- Figure 4-9 52
- Figure 4-9. Ethernet Menu 52
- Configuring the E3 Port 53
- Configuring the T3 Port 54
- Configuring the Bridge 55
- Configuring the MAC Table 56
- Configuring the Bridge Port 57
- Figure 4-16 58
- Figure 4-16. QoS Menu 58
- 4.3 Additional Tasks 59
- Chapter 6 62
- Figure 4-23 62
- Figure 4-23. MAC Table 62
- Figure 4-24 63
- Appendix B 64
- Figure 4-25 64
- Figure 4-25. File Transfer 64
- Chapter 5 65
- Resetting RICi-E3, RICi-T3 66
- Configuring a Typical 67
- Application 67
- 5.2 Connecting the Cables 68
- Connecting DC Power 69
- Building the MAC Table 71
- Diagnostics and 73
- Troubleshooting 73
- Figure 6-2 74
- Figure 6-2. E3 Statistics 74
- Figure 6-3 75
- Figure 6-3. T3 Statistics 75
- Displaying System Messages 76
- 6.2 Handling Alarms 77
- 6.3 Troubleshooting 78
- 6.4 Connectivity Tests 78
- Tracing the Route 79
- Loopback Test 80
- 6.5 Testing the Cables 81
- 6.6 Technical Support 82
- Pinouts 83
- Boot Manager 85
- Figure B-1 87
- DC power 93
- AD plug 93
- (top view) 93
- Supplement 95
- Customer Response Form 97
- Error Report 99
- Innovative Access Solutions 102
Manuais e produtos relacionados com Redes RAD Data comm FOM-E3
Redes RAD Data comm ASMI-450 Especificações
(133 páginas)
(133 páginas)
Redes RAD Data comm RICi-622GE Manual do Utilizador
(22 páginas)
(22 páginas)
Redes RAD Data comm ASMi-52L Especificações
(184 páginas)
(184 páginas)
Redes RAD Data comm FCD-X21 Manual do Utilizador
(4 páginas)
(4 páginas)
Redes RAD Data comm FCD-X21 Manual do Utilizador
(4 páginas)
(4 páginas)
Redes RAD Data comm 100 Especificações
(318 páginas)
(318 páginas)
Redes RAD Data comm ASMi-52L Especificações
(153 páginas)
(153 páginas)
Redes RAD Data comm T1 Especificações
(48 páginas)
(48 páginas)
Redes RAD Data comm FCD-V35 Manual do Utilizador
(6 páginas)
(6 páginas)
Redes RAD Data comm MBE10-8D Especificações
(50 páginas)
(50 páginas)
Redes RAD Data comm HCD-E1 Especificações
(150 páginas)
(150 páginas)
Redes RAD Data comm FCD-V35 Manual do Utilizador
(4 páginas)
(4 páginas)
Redes RAD Data comm FOMi-T1 Manual do Utilizador
(6 páginas)
(6 páginas)
Redes RAD Data comm MiRICi-E3T3 Especificações
(106 páginas)
(106 páginas)
Redes RAD Data comm 100 Especificações
(9 páginas)
(9 páginas)
Redes RAD Data comm ASM-60 Especificações
(90 páginas)
(90 páginas)
Yamaha Acústica manuales de usuario
Empezando en N
Comentários a estes Manuais