Rad-data-comm ASMI-450 Manual do Utilizador Página 59
- Página / 117
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ASMi-450 Installation and Operation Manual 4-1
Chapter 4
ASMi-450 Control
from the Control Port
4.1 General
This Chapter provides detailed instructions for the management of ASMi-450
by means of ASCII terminals and IP hosts using the Telnet protocol.
The initial configuration of the ASMi-450 must always be performed using a
standard ASCII terminal connected to the ASMi-450 control port, CONTROL
DCE. However, after performing the initial configuration, you can also manage
the ASMi-450 using any of the following three options:
• Use the terminal as a supervision terminal, for performing all the
management activities supported by the ASMi-450.
• Manage the ASMi-450 from any IP host using the Telnet protocol. After
establishing a Telnet session with the ASMi-450, the Telnet protocol offers
the same functionality as the supervision terminal, and in addition enables
remote access over IP networks.
• Manage the ASMi-450 by means of SNMP-based network management
stations, e.g., the RADview network management station offered by RAD,
using the SLIP protocol for communication.
The information presented in this chapter includes:
• Description of control terminal hardware requirements, communication and
handshaking - Section 4-2.
• Preparation for use of control terminal - Section 4-3.
• Description of control terminal set of commands and command syntax -
Section 4-4, 4-5.
• General operating instructions, including start-up, routine operations, and
stopping of remote control - Section 4-6.
• Configuration error messages - Section 4-7.
The instructions appearing in this Chapter assume that the supervision terminal
operator is familiar with the ASMi-450 system and with its configuration
parameters.
For instructions regarding the use of the RADview network management
station, refer to the RADview User's Reference Manual.
- ASMi-450 1
- Warranty 2
- Safety Warnings 3
- Telecommunication Safety 3
- Regulatory Information 4
- Declaration of Conformity 5
- Contents 10
- List of Figures 11
- List of Tables 13
- Quick-Start Guide 15
- 2. Configuration Procedure 16
- 3. Command Index 17
- Chapter 1 19
- Introduction 19
- Serial Data Port 20
- Characteristics 20
- Ethernet Interface 20
- HDSL Subsystem 21
- System Timing 22
- Control of 23
- Operation 23
- 1.2 Operating Environment 26
- HDSL Signal 27
- Structure 27
- HDSL-Related 27
- System Functions 27
- 1.3 Technical Specifications 28
- Chapter 2 31
- Installation 31
- 2.2 Unpacking 32
- 2.3 Site Requirements 32
- Opening ASMi-450 33
- Jumper and Switch 34
- Location and 34
- Functions 34
- . ASMi-450 Internal Settings 35
- Internal Settings 37
- Procedure 37
- Reinstalling 37
- ASMi-450 Cover 37
- 2.5 Connections 38
- Power Connection 39
- User's Port 39
- Connections 39
- HDSL Line 40
- Control Port 40
- Connection 40
- Chapter 3 41
- Front-Panel Operating 41
- Instructions 41
- Indicators 43
- General Operating 44
- Display Functions 44
- Organization of 46
- ASMi-450 Display 46
- Using Front-Panel 46
- Push-buttons 46
- Table 3-C. System Parameters 48
- Designation Function Values 48
- 3.6 Operating Instructions 50
- Normal Indications 51
- Fault Indications 52
- Turn-off 52
- Password 53
- Protection 53
- Configuration 53
- Step Action Key Display 54
- Specific 55
- Guidelines 55
- Chapter 4 59
- ASMi-450 Control 59
- 4.2 Hardware Requirements 60
- AUTOBAUD 62
- Function 62
- Supervision 63
- Terminal 63
- Language Syntax 64
- Command Options 64
- Protocol 64
- Index of 65
- Commands 65
- Command Purpose Options 66
- CLR ALM [/A] 67
- DEF AGENT 68
- DEF NAME 69
- DEF NODE 70
- DSP ST PORT [Option] 78
- DSP ST SYS [option] 79
- H<CR> 80
- Starting a Session 84
- - Single ASMi-450 84
- - Multiple ASMi-450 85
- Control Session 85
- Ending a Control 86
- Chapter 5 89
- Diagnostics 89
- 5.3 Test Functions 94
- TEST OPTIONS 95
- Operating 95
- 5.4 Power-Up Self-Test 96
- Appendix A 99
- Connector Wiring 99
- A.2 V.35 DCE Connector 101
- A.3 X.21 DCE Connector 102
- A.4 HDSL Line Connector 103
- Appendix B 105
- SNMP Management 105
- B.2 SNMP Environment 106
- Domains Under 108
- Management 108
- B.3 IP Environment 110
- B.4 SNMP Traps 112
- Appendix C 113
- Preparations 115
- Fastening the Two 116
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais