RAD Data comm ASM-20 Especificações Página 12
- Página / 116
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Quick Start Guide Installation and Operation Manual
2 Installing ASM-40 ASM-40 Ver. 1.0
DIP Switch Function Possible Settings Factory
Setting
the front panel pushbuttons OFF – The diagnostic tests cannot be activated
via the front panel
V54E section,
SW3/2
Controls activation of the local
digital loopback when remote
digital loopback is initiated
from the remote unit
ON – Local digital loopback activation is enabled
OFF – Local digital loopback activation is
disabled
ON
CNTE section,
SW3/3
Selects the transmit carrier
mode
ON – Carrier follows the RTS line
OFF – Carrier is constantly ON
OFF
Note: For ASM-40 units with G.703 Codirectional DTE interface, the CNTE section (SW3/3) must be set to OFF.
B/UB section,
SW3/4
Selects the line impedance:
Balanced: terminal block or DB-
15
Unbalanced: BNC
ON – 75Ω (for 32, 64, 128, 256, 512, 1024,
1920 and 2048 kbps)
OFF – 120Ω (for 32, 64, 128, 256, 512, 1024,
1920 and 2048 kbps)
According to
the connector
type
Note: 100Ω line impedance is set by selecting one of the following data rates: 192, 384, 768, 1536 and 1544 kbps. In
this case, the settings of the SW3 B/UB section are ignored.
ALBE section,
SW3/5
Enables local analog loopback
activation from the DTE
(via pin 18 for V.24, RS-530,
V.36 or via pin “JJ” for V.35)
ON – The local analog loopback activation from
the DTE is enabled
OFF – The local analog loopback activation from
the DTE is disabled
OFF
Note
:
Set this section to DIS if the DTE interface does not support the local analog loopback activation via the
appropriate pin.
RLBE section,
SW3/6
Enables remote digital loopback
activation from the DTE (via pin
21 for V.24, RS-530, V.36 or
via pin “HH” for V.35)
ON – The remote digital loopback activation
from the DTE is enabled
OFF – The remote digital loopback activation
from the DTE is disabled
OFF
Note
:
Set this section to DIS if the DTE interface does not support the remote digital loopback activation via the
appropriate pin.
SW5 Selects data rate
SW54
SW53 SW52 SW51
0 0 0 0 2048
0 0 0 1 1920
0 0 1 0 1544
0 0 1 1 1536
0 1 0 0 1024
0 1 0 1 768
0 1 1 0 512
0 1 1 1 384
1 0 0 0 256
1 0 0 1 192
1 0 1 0 128
1 0 1 1 64
1 1 0 0 32
256
- High-Speed Short-Range Modem 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating ASM-40 13
- • DCD: On 14
- • TEST: Off 14
- Contents 15
- Chapter 1 17
- Introduction 17
- Features 18
- 1.2 Physical Description 19
- 1.3 Functional Description 19
- Timing Generator 20
- G.703-HDB3 Interface Timing 21
- Encoder/Decoder 22
- Line Driver 22
- 1.4 Technical Specifications 23
- Chapter 2 27
- Installation and Setup 27
- 2.2 Package Contents 28
- 2.3 Installation and Setup 28
- MT RCV GND 31
- Connecting the Line 32
- Connecting the DTE 32
- Connecting the Power 33
- Chapter 3 35
- Operation 35
- 3.2 Operating Procedure 36
- Normal Indications 37
- Turning ASM-40 Off 37
- Chapter 4 39
- Troubleshooting and 39
- Diagnostics 39
- Local Analog Loopback (LLB) 40
- Local Digital Loopback (DIG) 41
- Local ASM-40 Remote ASM-40 42
- 4.2 Internal BERT 42
- Two-BERT Test 43
- ASM-40 ASM-40 44
- Chapter 5 45
- ASM-40/R Card 45
- AC Supply 46
- 5.3 ASM-40/R Front Panel 47
- Figure 2-1 49
- Table 2-1 49
- Figure 5-4 49
- Connecting the Interfaces 51
- Appendix A 53
- Pinouts 53
- Table A-2 56
- Connection 57
- Chassis Ground 58
- RCV1* (input) 58
- RCV2 (input) 58
- XMT1 (output) 58
- XMT2* (output) 58
- Table A-6 59
- Appendix B 61
- IR-ETH Interface Module 61
- XMT RCV GND 62
- General 62
- Opening the ASM-40 Case 63
- Setting the DIP Switch 64
- Closing the ASM-40 Case 64
- LED Indicators 64
- Connecting the LAN 65
- Appendix C 67
- IR-ETH/QN (IR-ETH/Q) 67
- Interface Module 67
- ACT LINK 68
- IR-ETH/QN 68
- Setting the DIP Switches 70
- Appendix D 73
- IR-IP Interface Module 73
- D.2 Technical Specifications 74
- D.3 Physical Description 74
- IR-IP LEDs 75
- Connecting the Telnet Host 79
- What to Do If 81
- General Operating Procedures 82
- Figure D-5. IR-IP Main Menu 83
- Figure D-6 83
- D.7 Quick Setup Menu 84
- WAN IP Address 85
- WAN IP Mask 85
- Default Gateway 85
- D.8 Management Access Menu 86
- D.9 Advanced Setup Menu 87
- Device Identification Menu 88
- Interface Parameters Menu 88
- LAN Status 89
- WAN Status 89
- WAN Throttle 89
- Quick Setup Menu 90
- Figure D-7 90
- Figure D-13 90
- Protocol Field Compression 91
- Authentication Protocol 91
- Security Host/Guest 91
- User Name To Send 92
- Password To Send 92
- User Name To Accept 92
- Password To Accept 92
- Multicast IP Menu 93
- D.10 Device Control Menu 94
- New Software Download Menu 95
- View Error Log Screen 96
- Resets Menu 96
- Reset Device 97
- Reset LAN 97
- Reset WAN 97
- D.11 View Menu 98
- ARP Tables 99
- Statistics Screen 100
- Figure D-26 101
- Using the Ping Function 102
- D.14 Erasing IR-IP Software 104
- Performing 105
- Preliminary Configuration 105
- IR-G.703 Interface Module 107
- Appendix E 107
- EXT Timing 108
- INT/RCV Timing 109
- Customer Response Form 111
- Error Report 113
- Innovative Access Solutions 116
Manuais e produtos relacionados com Redes RAD Data comm ASM-20
Redes RAD Data comm T1 Especificações
(34 páginas)
(34 páginas)
Redes RAD Data comm Optimux-34 Informações Técnicas
(82 páginas)
(82 páginas)
Redes RAD Data comm FOM-E3 Manual do Utilizador
(2 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais