RAD Data comm Optimux-34 Especificações Página 5
- Página / 118
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
General Safety Instructions
The following instructions serve as a general guide for the safe installation and operation of
telecommunications products. Additional instructions, if applicable, are included inside the
manual.
Safety Symbols
This symbol may appear on the equipment or in the text. It indicates potential
safety hazards regarding product operation or maintenance to operator or service
personnel.
Danger of electric shock! Avoid any contact with the marked surface while the
product is energized or connected to outdoor telecommunication lines.
Protective ground: the marked lug or terminal should be connected to the building
protective ground bus.
Some products may be equipped with a laser diode. In such cases, a label with the
laser class and other warnings as applicable will be attached near the optical
transmitter. The laser warning symbol may be also attached.
Please observe the following precautions:
• Before turning on the equipment, make sure that the fiber optic cable is intact
and is connected to the transmitter.
• Do not attempt to adjust the laser drive current.
• Do not use broken or unterminated fiber-optic cables/connectors or look
straight at the laser beam.
• The use of optical devices with the equipment will increase eye hazard.
• Use of controls, adjustments or performing procedures other than those
specified herein, may result in hazardous radiation exposure.
ATTENTION: The laser beam may be invisible!
In some cases, the users may insert their own SFP laser transceivers into the product. Users are
alerted that RAD cannot be held responsible for any damage that may result if non-compliant
transceivers are used. In particular, users are warned to use only agency approved products that
comply with the local laser safety regulations for Class 1 laser products.
Always observe standard safety precautions during installation, operation and maintenance of
this product. Only qualified and authorized service personnel should carry out adjustment,
maintenance or repairs to this product. No installation, adjustment, maintenance or repairs
should be performed by either the operator or the user.
Warning
Warning
- Optimux-34 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- 3. Configuring Optimux-34 18
- Selecting the Clock Source 19
- Contents 21
- Optimux-34 Ver. 2.81 iii 23
- Chapter 1 25
- Introduction 25
- Point-to-Point Application 26
- Wireless Link Application 27
- Application 28
- 1.2 Physical Description 29
- 1.3 Functional Description 30
- Power Supply Redundancy 31
- Link Redundancy 31
- Management Requirements 32
- Clocking 32
- Power Requirements 33
- Optimux-34 Ver. 2.81 34
- Chapter 2 37
- Installation and Setup 37
- 2.3 Required Equipment 38
- 2.4 Mounting the Unit 38
- Appendix A 40
- Warning 40
- Caution 40
- Connecting to E3 Link 41
- Connecting to Alarm Relay 42
- 2.7 Connecting to Power 43
- Chapter 3 45
- Operation 45
- 3.3 Default Settings 48
- RADview-TDM 50
- User's Manual 50
- Chapter 4 50
- Starting a Control Session 51
- Choosing Options 51
- Correcting Entries 52
- Navigating Data Forms 52
- Web Browser Requirements 54
- Working with RADview 55
- 3.5 Menu Map 56
- 3.6 Turning Off Optimux-34 57
- Chapter 4 59
- Configuration 59
- Chapter 1 60
- Setting up the Manager List 64
- Management Access 65
- Configuring the Control Port 66
- Configuring Security Timeout 68
- Setting the Alarms 68
- Configuring the E3 Port 72
- Configuring the E1 Port 73
- Configuring the V.35 Port 74
- 4-19. Change Access Menu 76
- 4-20. User Info Menu 77
- 4-21. Factory Default Menu 77
- Viewing the Inventory 78
- RAD Technical Support 81
- Chapter 6 81
- Downloading the License File 81
- Activating the License File 82
- Chapter 5 85
- Monitoring and 85
- Diagnostics 85
- Event Log 86
- System Status 87
- Interface Status 88
- 5.2 Detecting Errors 90
- Loop Connections 91
- 5.5 Technical Support 96
- Chapter 6 97
- Software Upgrade 97
- 6.4 Prerequisites 98
- Utilities Menu 98
- Activating the TFTP Server 99
- 6-2. TFTP Menu 100
- 6-1. TFTP Values 101
- Using the XMODEM Protocol 103
- Using the TFTP 105
- Appendix A 107
- Pinouts 107
- Optimux-34 Ver. 2.81 108
- A.3 Alarm Connector 109
- A.4 Control Connector 110
- A.5 Power Connectors 110
- A.6 V.35 Connectors 110
- A-5. V.35/ISO-2110 Pinout 111
- A-6. V.35/Telebras Pinout 112
- Customer Response Form 113
- Error Report 115
- The Access Company 118
Manuais e produtos relacionados com Redes RAD Data comm Optimux-34
Redes RAD Data comm ASMi-31 Especificações
(114 páginas)
(114 páginas)
Redes RAD Data comm ASM-60 Especificações
(30 páginas)
(30 páginas)
Redes RAD Data comm FCD-V35 Especificações
(228 páginas)
(228 páginas)
Redes RAD Data comm FCD-IP Manual do Utilizador
(110 páginas)
(110 páginas)
Redes RAD Data comm ASMi-52 Informações Técnicas
(100 páginas)
(100 páginas)
Redes RAD Data comm FOM-T3 Especificações
(42 páginas)
(42 páginas)
Redes RAD Data comm Optimux-106 Especificações
(110 páginas)
(110 páginas)
Redes RAD Data comm ASM-20 Especificações
(116 páginas)
(116 páginas)
Redes RAD Data comm T1 Especificações
(34 páginas)
(34 páginas)
Redes RAD Data comm Optimux-34 Informações Técnicas
(82 páginas)
(82 páginas)
Redes RAD Data comm FOM-E3 Manual do Utilizador
(2 páginas)
(2 páginas)
Sagem 288140594 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia wielofunkcyjne Sagem 288140594.
Dostarczamy 1 pdf podręczników Sagem 288140594 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comentários a estes Manuais