Rad-data-comm E1 Interface Converter RIC-E1 Manual do Utilizador Página 68
- Página / 99
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Appendix D IR-IP Interface Module RIC-E1 Installation and Operation Manual
D-12 IR-IP Management Utility
D.6 IR-IP Management Utility
General Operating Procedures
The IR-IP interface module is managed via a simple, menu-driven utility that uses a
basic terminal user interface. A typical screen is shown in Figure D-6.
As seen in Figure D-6, each screen has a header that identifies the device being
configured and its logical name, assigned by the user, followed by the running
software revision and date. The bottom line of the screen displays prompts that
guide you in the execution of the various activities.
Use the following general procedures to perform the desired activity:
• To change a parameter or to select a menu item, type the corresponding line
number.
• For a parameter, which has a discrete set of values, the parameter values are
enclosed in brackets [ ]. To select a new value, press the spacebar to scroll
among the available values until the desired value is displayed, and then press
<Enter> to select the displayed value.
• To enter a value that requires free text entry, type in the desired string and
then press <Enter>. Use backspace to erase the current string.
• After all the parameters have been selected, a prompt appears, requesting that
you confirm the changes.
For proper display of the screens, you must:
• Select a fixed-pitch system font for the display. Use your operating system
documentation to find how to select a proper font.
• Configure the Telnet utility to use VT-100 terminal emulation.
Starting a Management Utility
The management utility is started automatically when Telnet communication is
established. If password protection is enabled (see the Management Access Menu
section below), you will be prompted to enter the Telnet password. The opening
screen, which appears after the Telnet session activation, is the IR-IP Main menu
(see Figure D-6).
IR_IP <IR-IP> S/W Ver. 1.21 31/IR (date)
1. Quick Setup
2. Management Access
3. Advanced Setup
4. Device Control
5. View
6. Diagnostic Tool (PING terminal)
Press one of the numbers to select or ESC:
Figure D-6. IR-IP Main Menu
To end the utility, press <Esc> when the Main menu is displayed. This will also
end the Telnet session.
Note
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
www.bestdatasource.com
- E1 Interface Converter 1
- Limited Warranty 4
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 8
- Declaration of Conformity 10
- Quick Start Guide 11
- 2. Operating RIC-E1 12
- Contents 13
- List of Figures 14
- List of Tables 14
- Chapter 1 15
- Introduction 15
- 1.2 Physical Description 16
- 1.3 Functional Description 17
- 1.4 Technical Specifications 18
- Order from: Cutter Networks 19
- Chapter 2 21
- Installation and Setup 21
- 2.3 Configuring RIC-E1 22
- Configuring RIC-E1 2-3 23
- Connecting the Interfaces 24
- Connecting the DTE 25
- Connecting the AC Power 25
- Connecting the DC Power 25
- 2-6 Configuring RIC-E1 26
- Chapter 3 27
- Operation 27
- 3.2 Operating Instructions 28
- Chapter 4 29
- Troubleshooting and 29
- Diagnostics 29
- 4.2 Troubleshooting 30
- 4.3 Technical Support 31
- 4-4 Technical Support 32
- Chapter 5 33
- RIC-E1/R Card 33
- 5-2 ASM-MN-214 Card Cage 34
- 5.2 Power Supply 35
- 5.3 RIC-E1/R Front Panel 36
- Warning 40
- Appendix A 41
- Interface Connector Wiring 41
- [Indication] 41
- [Function] 42
- [Signal 42
- Timing] 42
- A.3 Line Interface Connector 43
- Appendix B 45
- IR-ETH Interface Module 45
- 10B ASE-T 46
- IR-ETH Options B-3 47
- B.3 Technical Specifications 48
- Setting the DIP Switch 49
- LED Indicators 49
- Connecting the LAN 50
- C.1 Introduction 51
- 10/100BASE-T 52
- C.3 Technical Specifications 54
- Setting the DIP Switches 55
- Appendix D 57
- IR-IP Interface Module 57
- D.1 Introduction 58
- 10BaseT LAN 59
- D.3 Physical Description 60
- IR-IP LEDs 61
- IR-IP Controls 61
- Rescue Configuration 64
- IP Learning Mechanism 65
- What to Do If 67
- D.6 IR-IP Management Utility 68
- D.7 Quick Setup Menu 69
- LAN IP Address 70
- LAN IP Mask 70
- WAN IP Address 70
- WAN IP Mask 70
- Default Gateway 70
- RIC-E1 with IR-IP 71
- DHCP Server 71
- LAN IP Address: 192.168.1.2 71
- Mask: 255.255.255.248 71
- IP Network 71
- D.8 Management Access Menu 72
- D.9 Advanced Setup Menu 73
- Device Name 74
- Contact Person 74
- System Location 74
- Advanced Setup Menu D-19 75
- Protocol Field Compression 76
- Authentication Protocol 76
- Security Host/Guest 77
- User Name To Send 77
- Password To Send 77
- User Name To Accept 77
- Password To Accept 77
- Multicast Forwarding 78
- Static Groups 79
- Total Timeout 80
- Start Operation 80
- Server IP Address 80
- File Name 80
- Resetting the Device 81
- Resetting the LAN Interface 81
- Resetting the WAN Interface 82
- ARP Tables 83
- Displaying Statistics 84
- Using the Ping Function 86
- D.14 Erasing IR-IP Software 87
- Erasing Application Software 88
- Downloading New Software 88
- E.1 Introduction 90
- EXT INT/LBT 91
- INT/LBT Clock Mode 92
- Customer Response Form 96
- Error Report 97
Manuais e produtos relacionados com Hardware Rad-data-comm E1 Interface Converter RIC-E1
(50 páginas)Sagem 288140594 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia wielofunkcyjne Sagem 288140594.
Dostarczamy 1 pdf podręczników Sagem 288140594 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comentários a estes Manuais