RAD Data comm IPmux-8 Especificações Página 8
- Página / 174
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Always make sure that the equipment is grounded before connecting telecommunication cables. Do
not disconnect the ground connection before disconnecting all telecommunications cables.
Some SELV and non-SELV circuits use the same connectors. Use caution when connecting cables.
Extra caution should be exercised during thunderstorms.
When using shielded or coaxial cables, verify that there is a good ground connection at both ends. The
earthing and bonding of the ground connections should comply with the local codes.
The telecommunication wiring in the building may be damaged or present a fire hazard in case of
contact between exposed external wires and the AC power lines. In order to reduce the risk, there are
restrictions on the diameter of wires in the telecom cables, between the equipment and the mating
connectors.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords.
Pour réduire les risques s’incendie, utiliser seulement des conducteurs de
télécommunications 26 AWG ou de section supérieure.
Some ports are suitable for connection to intra-building or non-exposed wiring or cabling only. In such
cases, a notice will be given in the installation instructions.
Do not attempt to tamper with any carrier-provided equipment or connection hardware.
Electromagnetic Compatibility (EMC)
The equipment is designed and approved to comply with the electromagnetic regulations of major
regulatory bodies. The following instructions may enhance the performance of the equipment and will
provide better protection against excessive emission and better immunity against disturbances.
A good earth connection is essential. When installing the equipment in a rack, make sure to remove all
traces of paint from the mounting points. Use suitable lock-washers and torque. If an external
grounding lug is provided, connect it to the earth bus using braided wire as short as possible.
The equipment is designed to comply with EMC requirements when connecting it with unshielded
twisted pair (UTP) cables. However, the use of shielded wires is always recommended, especially for
high-rate data. In some cases, when unshielded wires are used, ferrite cores should be installed on
certain cables. In such cases, special instructions are provided in the manual.
Disconnect all wires which are not in permanent use, such as cables used for one-time configuration.
The compliance of the equipment with the regulations for conducted emission on the data lines is
dependent on the cable quality. The emission is tested for UTP with 80 dB longitudinal conversion loss
(LCL).
Unless otherwise specified or described in the manual, TNV-1 and TNV-3 ports provide secondary
protection against surges on the data lines. Primary protectors should be provided in the building
installation.
The equipment is designed to provide adequate protection against electro-static discharge (ESD).
However, it is good working practice to use caution when connecting cables terminated with plastic
connectors (without a grounded metal hood, such as flat cables) to sensitive data lines. Before
connecting such cables, discharge yourself by touching earth ground or wear an ESD preventive wrist
strap.
Caution
A
ttentio
n
- TDM Pseudowire Access 1
- Gateways 1
- IPmux-8, IPmux-16 3
- Limited Warranty 4
- General Safety Instructions 5
- Product Disposal 5
- Handling Energized Products 6
- FCC-15 User Information 9
- Declaration of Conformity 10
- Conventions 12
- Quick Start Guide 13
- Contents 15
- IPmux-8/16 Ver. 6.00 iii 17
- Chapter 1 19
- Introduction 19
- Applications 20
- Features 21
- 4-Port Ethernet Module 23
- 1-Port Ethernet Module 24
- Default Next Hop per Host 24
- Download (DL) Transparent 25
- Operation Modes for E1/T1 25
- Multibundling 25
- 1.2 Physical Description 27
- 1.3 Functional Description 28
- Unframed 29
- External Network Timing 30
- Single Source Clock Network 31
- Bundle Redundancy 32
- Frame Format 32
- MAC IP UDP CW 33
- VLAN Support 34
- Packet Delay Variation 35
- PDVT (Jitter) Buffer 36
- Packetization Delay 36
- Round Trip Delay 37
- Ethernet 37
- Ethernet Redundancy 38
- Load Sharing 38
- Rate Limiter Option 39
- Table 1-5. Mode A 40
- Table 1-6. Mode B 40
- Table 1-7. Mode C 40
- Table 1-8. Mode D 41
- Table 1-9. Mode E 41
- Table 1-10. Mode F 41
- Ethernet Throughput 42
- End-to-End Alarm Generation 43
- Management 44
- 1.4 Technical Specifications 45
- Environment 49
- Chapter 2 51
- Installation and Setup 51
- 2.3 Package Contents 52
- ~100 -24 0VAC 3A T 125V 53
- ~100-240VAC 3A T 125V 53
- Installing SFP Transceivers 55
- To connect to an NMS: 57
- Connecting AC Power 58
- Connecting DC Power 59
- Chapter 3 61
- Operation 61
- IPmux-16 63
- 3.3 Default Settings 64
- To enter as a superuser: 67
- To enter as a user: 67
- Overview of Menu Operations 68
- Configuration 69
- Physical Layer Configuration 69
- Timeslot Configuration 70
- IP Support 70
- To power off IPmux-8: 71
- To power off IPmux-16: 71
- Chapter 4 73
- Defining Network Managers 76
- Configuring Default Gateway 78
- Controlling Telnet Access 79
- Controlling SNMP Access 79
- Configuring Ethernet Bridge 84
- Defining VLANs 85
- Configuring E1 Interface 86
- Configuring T1 Interface 88
- 0–F (ESF) 90
- 0–3 (D4) 90
- 3, 4 for the slot 95
- 1–4 or 1–8 for the link 95
- Connecting Bundles 96
- 496 (E1), 384 (T1) 96
- Configuring IP ToS Support 103
- 4.3 Additional Tasks 105
- Setting Date and Time 106
- Managing File System 107
- Type Y to confirm 108
- Transferring Files via TFTP 109
- Resetting IPmux-8/16 110
- Chapter 5 113
- Configuring for a Typical 113
- Application 113
- Configuration Summary Table 114
- 5.3 Configuring IPmux-16 116
- Configuring Bundles 117
- IPmux-8/16 Ver. 6.00 118
- Chapter 6 121
- Troubleshooting and 121
- Diagnostics 121
- Fragments 124
- Displaying E1/T1 Statistics 125
- Displaying E3/T3 Statistics 129
- Displaying Events 141
- Clearing Events 142
- Masking Alarm Traps 143
- Working with Alarm Relay 145
- 6.3 Testing the Units 146
- Remote IPmux-16 147
- IP/Ethernet 147
- Running Ping Test 148
- Tracing the Route 149
- 6.4 Troubleshooting 150
- 6.6 Technical Support 153
- Appendix A 155
- Interface Connector 155
- Specifications 155
- A.3 CONTROL Connector 156
- Cross Cable Wiring 157
- A.4 Alarm Connector 158
- A.5 External Clock Connector 158
- Appendix B 159
- Boot Sequence for 159
- Downloading Software 159
- Boot Sequence 160
- Accessing the Boot Menu 160
- Appendix C 161
- SNMP Management 161
- MIB Structure 162
- SNMP Communities 163
- Authentication 164
- Network Management Stations 164
- Customer Response Form 169
- Error Report 171
Manuais e produtos relacionados com Gateways/controladores RAD Data comm IPmux-8
(192 páginas)Yamaha Acústica manuales de usuario
Empezando en N
Comentários a estes Manuais