RAD Data comm FCD-X21 Manual do Utilizador descarregar pdf (Página 4)

 1991–2003 RAD Data Communications Ltd. Specifications are subject to change without prior notice.

All other trademarks are the property of their respective holders.

FCD-E1L, FCD-T1L

E1/T1 or Fractional E1/T1 Managed Access Units

data communications

www.rad.com

International Headquarters

24 Raoul Wallenberg

Street

Tel Aviv 69719, Israel

Tel: (972) 3-6458181

Fax: (972) 3-6498250, 6474436

Email: [email protected]

U.S. Headquarters

900 Corporate Drive

Mahwah, NJ 07430

Tel: (201) 529-1100

Toll free: 1-800-444-7234

Fax: (201) 529-5777

Email: [email protected]

165-100-10/03165-100-10/03

• Timeslot Allocation

Consecutive (bundled)

User-defined

• Management Port



Interface and connector:

V.24/RS-232, 9-pin D-type,

female



Format: Asynchronous



Baud rate: 1.2-19.2 kbps,

autobaud



Character: 8 bit no parity, 7 bit

odd or even parity

• Indicators

General: PWR (green), TST

(yellow), ALM MAJ, ALM MIN

(red), AUTO CONFIGURATION

Main E1: LOC SYNC LOSS (red),

REM SYNC LOSS (red)

Main T1: RED ALARM (red), YEL

ALARM (yellow)

• Front Panel Controls

Single push-button for auto

configuration

• Alarms

Last 100 alarms are stored and

available for retrieval. Each alarm is

time stamped.

• Physical

Height: 4.4 cm / 1.75 in

Width: 21.5 cm / 8.5 in

Depth: 24.3 cm / 9.6 in

Weight 0.9 kg / 2.0 lb

• Power

AC: 100 to 240 VAC; 47 to 63 Hz

DC: -48 VDC (-40 to -57 VDC)

Power consumption: 5W max.

• Environment

Temperature: 0-50°C / 32-122°F

Humidity: up to 90%,

non condensing

ORDERING

FCD-E1L/*/~/&/%

E1/Fractional E1 Access Unit

FCD-T1L/~/&/%

T1/Fractional T1 Access Unit

* Specify E1 main link interface

type:

B for balanced with RJ-45

connector

U for unbalanced with BNC

connector

~ Specify power supply voltage:

AC for 110 VAC to 240 VAC

48 for -48 VDC

& Specify data port interface:

530 for RS-530

V35 for V.35

X21 for X.21

449 for V.36/RS-449

% Specify optional second data port

interface:

530 for RS-530 interface

V35 for V.35 interface

X21 for X.21 interface

V24 for V.24 interface

449 for RS-449 interface

ETQN for UTP Ethernet bridge

VLAN (10/100BaseT)

ETUB for UTP Ethernet bridge

(10BaseT)

ETBB for BNC Ethernet bridge

(10Base2)

ETUQ for UTP Ethernet bridge

VLAN (10BaseT)

ETBQ for BNC Ethernet bridge

VLAN (10Base2)

ETUR for UTP Ethernet router

(10BaseT)

ETBR for BNC Ethernet router

(10Base2)

CABLES

The following cables convert

FCD-E1L’s or FCD-T1’s 25-pin data

port connectors into the respective

interface. Cable length is 2m (6 ft).

CBL-HS2/*/#

Adapter cables for DB-25 channel

connectors

* Specify interface, clock mode:

V/1 for 34-pin V.35, DCE

V/2 for 34-pin V.35, DTE1

V/3 for 34-pin V.35, DTE2

R/1 for 37-pin V.36/RS-449, DCE

R/2 for 37-pin V.36/RS-449, DTE1

R/3 for 37-pin V.36/RS-449, DTE2

X/1 for 15-pin X.21, DCE

# Specify cable connector type:

F for female

M for male

Note: Cables for DCE clock mode

operation are supplied for each data port

according to interface option specified.

Cables for DTE1 and DTE2 mode

operation must be ordered separately.

RM-28

Hardware for mounting one or two

units in a 19" rack

Table 1. Ethernet Interface Modules Characteristics

Interface

Module

LAN Table

[addresses]

Filtering &

Forwarding

[frames per second]

Buffer

[frames]

Line Code WAN Protocol

IR-ETH 10,000 15,000 256 Manchester HDLC

IR-ETH/Q 2,000 2,000 256 Manchester HDLC

IR-ETH/QN 1,024 150,000 85  10BaseT: Manchester

 100BaseT: MLT3

HDLC

IR-IP – – 256 Manchester  PPP (PAP/CHAP)

 Frame Relay (RFC 1490)

 HDLC

Note: All the Ethernet interface modules conform to the IEEE 802.3/Ethernet V2 standard. Additionally, IR-ETH/Q supports IEEE

802.1/q frames, and IR-ETH/QN conforms to IEEE 802.1q (relevant parts), 802.1p and 802.3x.

1 2 3 4

FCD-E1L, FCD-T1L 1

Comentários a estes Manuais

Sem comentários

RAD Data comm FCD-X21 Manual do Utilizador Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Redes RAD Data comm FCD-X21