RAD Data comm Optimux-108 Especificações Página 8
- Página / 132
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
When using shielded or coaxial cables, verify that there is a good ground connection at both
ends. The grounding and bonding of the ground connections should comply with the local codes.
The telecommunication wiring in the building may be damaged or present a fire hazard in case of
contact between exposed external wires and the AC power lines. In order to reduce the risk,
there are restrictions on the diameter of wires in the telecom cables, between the equipment
and the mating connectors.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line
cords.
Pour réduire les risques s’incendie, utiliser seulement des conducteurs de
télécommunications 26 AWG ou de section supérieure.
Some ports are suitable for connection to intra-building or non-exposed wiring or cabling only. In
such cases, a notice will be given in the installation instructions.
Do not attempt to tamper with any carrier-provided equipment or connection hardware.
Electromagnetic Compatibility (EMC)
The equipment is designed and approved to comply with the electromagnetic regulations of
major regulatory bodies. The following instructions may enhance the performance of the
equipment and will provide better protection against excessive emission and better immunity
against disturbances.
A good ground connection is essential. When installing the equipment in a rack, make sure to
remove all traces of paint from the mounting points. Use suitable lock-washers and torque. If an
external grounding lug is provided, connect it to the ground bus using braided wire as short as
possible.
The equipment is designed to comply with EMC requirements when connecting it with unshielded
twisted pair (UTP) cables. However, the use of shielded wires is always recommended, especially
for high-rate data. In some cases, when unshielded wires are used, ferrite cores should be
installed on certain cables. In such cases, special instructions are provided in the manual.
Disconnect all wires which are not in permanent use, such as cables used for one-time
configuration.
The compliance of the equipment with the regulations for conducted emission on the data lines
is dependent on the cable quality. The emission is tested for UTP with 80 dB longitudinal
conversion loss (LCL).
Unless otherwise specified or described in the manual, TNV-1 and TNV-3 ports provide secondary
protection against surges on the data lines. Primary protectors should be provided in the building
installation.
The equipment is designed to provide adequate protection against electro-static discharge (ESD).
However, it is good working practice to use caution when connecting cables terminated with
plastic connectors (without a grounded metal hood, such as flat cables) to sensitive data lines.
Before connecting such cables, discharge yourself by touching ground or wear an ESD preventive
wrist strap.
Caution
Attention
- Optimux-108 1
- Limited Warranty 4
- Product Disposal 4
- General Safety Instructions 5
- Safety Symbols 5
- Handling Energized Products 6
- Caution 8
- Attention 8
- FCC-15 User Information 9
- Mise au rebut du produit 10
- Symboles de sécurité 10
- Français 11
- Glossary 13
- Quick Start Guide 17
- 2. Connecting the Power 18
- Configuring the MNG-ETH port 19
- Contents 21
- Optimux-108 Ver. 6.1 iii 23
- Appendix A. Pinouts 24
- Chapter 1 25
- Introduction 25
- Features 26
- 1.2 Physical Description 27
- Technical Characteristics 28
- Uplink Redundancy Option 29
- V.35 User Port 30
- Ethernet User Port 30
- Uplink and Tributaries 31
- Rear Panel Alarm Connector 32
- Management 33
- Plastic Enclosure 35
- Metal Enclosure 36
- Chapter 2 37
- Installation and Setup 37
- 2.2 Package Contents 38
- 2.3 Required Equipment 38
- 2.4 Mounting the Unit 38
- Connector Location 39
- Connecting the Uplink 41
- Alarm Connector 43
- 2.6 Connecting to Power 44
- 2 Installation and Setup 45
- Chapter 3 47
- Operation 47
- Rear Panel Indicators 48
- 3.3 Default Settings 49
- Working with Terminal 51
- 3-3. Password Prompt Screen 52
- Choosing Options 53
- Navigating the Screens 53
- Web Browser Requirements 54
- Third-party SNMP-based NMS 58
- 3.5 Menu Map 59
- 3.6 Turning Off the Unit 61
- Chapter 4 63
- Configuration 63
- Setting up the Manager List 65
- Listing Users 66
- Configuring Security Timeout 68
- Displaying New Alarms 68
- Configuring V.35 Parameters 72
- 4-14. V.35 Menu 73
- 4-4. V.35 Parameters 73
- Configuring Local Redundancy 74
- Chapter 6 77
- Ethernet Ports 80
- Uplink 81
- E1 Tributary Ports 82
- V.35 Port 83
- Changing a Password 84
- Appendix B 85
- 4-30. File System Menu 85
- Swapping the Software Files 86
- Resetting Factory Defaults 86
- Resetting Optimux-108 87
- Diagnostics 89
- Chapter 5 89
- Monitoring and 89
- 5-2. System Status Screen 90
- • Enter 1 91
- 5-7. E1 Port Status Screen 95
- 5.2 Detecting Problems 96
- 5.3 Handling Events 97
- Clearing Events 98
- Displaying Active Alarms 99
- Masking Alarms 100
- 5.4 Troubleshooting 101
- 5-12. Diagnostics Menu 102
- Local Optimux-108 103
- E1 Tributary Local Loopback 104
- 5.7 Technical Support 108
- Chapter 6 109
- Software Upgrade 109
- Utilities Menu 110
- Activating the TFTP Server 111
- Telnet 113
- Using the XMODEM Protocol 114
- Using the TFTP 116
- Chapter 7 119
- Configuring a Typical 119
- Application 119
- Appendix A 121
- Pinouts 121
- A.2 Control Port Connector 122
- Interface, respectively 124
- Customer Response Form 127
- Error Report 129
- The Access Company 132
Sagem 288140594 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia wielofunkcyjne Sagem 288140594.
Dostarczamy 1 pdf podręczników Sagem 288140594 do pobrania za darmo według typów dokumentów: Arkusz Danych
Comentários a estes Manuais