RAD Data comm IPmux-11 Especificações Página 11
- Página / 148
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
IPmux-11 Ver. 2.00 Configuring IPmux-11 1
Quick Start Guide
Installation of IPmux-11 should be carried out only by an experienced technician.
If you are familiar with IPmux-11, use this guide to prepare the unit for operation.
1. Installing IPmux-11
Connecting the Interfaces
1. Connect the network to the RJ-45 connector designated ETH 1.
2. Connect the user LAN(s) to the RJ-45 connector(s) designated ETH 2 or ETH 3.
3. Connect the E1 or T1 line to the RJ-45 connector designated E1 or T1.
When connecting balanced E1 or T1 equipment, make sure to use only 4-wire
RJ-45 connectors with the following pins used for receiving and transmitting data:
1, 2, 4, 5. Do not use 8-pin RJ-45 connectors.
4. Connect the control terminal to the rear panel CONTROL connector.
or
Connect a Telnet host, or a PC running a Web browsing application to one of
the user LAN ports.
Connecting the Power
• Connect the power cable to the power connector on the IPmux-11 rear panel.
The unit has no power switch. Operation starts when the power is applied
to the rear panel power connector.
2. Configuring IPmux-11
Configure IPmux-11 to the desired operation mode via an ASCII terminal connected
to the rear panel CONTROL port. Alternatively, you can manage IPmux-11 over
Telnet, or via a PC running a Web browsing application connected to one of the user
LAN ports.
Starting a Terminal Session for the First Time
To start a terminal session:
1. Connect a terminal to the CONTROL connector of IPmux-11.
2. Turn on the control terminal PC and set its port parameters to 115,200 baud,
8 bits/character, 1 stop bit, no parity. Set the terminal emulator to ANSI VT100
emulation (for optimal view of system menus).
3. Power IPmux-11 up and proceed with management session.
Caution
- IPmux-11 1
- Limited Warranty 4
- Product Disposal 5
- General Safety Instructions 5
- Handling Energized Products 6
- FCC-15 User Information 9
- Declaration of Conformity 10
- 1. Installing IPmux-11 11
- 2. Configuring IPmux-11 11
- Contents 13
- 1.1 Overview 15
- E1 Interface 16
- T1 Interface 16
- Ethernet Interface 16
- TDMoIP Operation Modes 17
- Management 18
- 1.2 Physical Description 19
- 1.3 Functional Description 19
- Unframed 20
- Fractional 20
- Fractional with CAS 20
- External Network Timing 21
- Single Source Clock Network 22
- 1 Fragment Offset (least) 23
- VLAN Support 24
- UDP Support 24
- TDMoMPLS 24
- Packets Leaving IPmux-11 25
- Packets Arriving 25
- PDVT (Jitter) Buffer 26
- Ethernet Throughput 26
- Round Trip Delay 28
- OAM Connectivity 29
- End-to-End Alarm Generation 29
- Trail-Extended Mode 29
- VLAN Traffic Behavior 30
- Ethernet Ports 30
- Switch Operation Modes 31
- Table 1-12. Mode C 34
- Table 1-13. Mode D 34
- Table 1-14. Mode E 35
- Table 1-15. Mode F 35
- 1.4 Technical Specifications 38
- 2.1 Introduction 41
- 2.3 Package Contents 42
- Connecting AC Power 45
- Connecting DC Power 45
- IPmux -11 47
- 3.3 Default Settings 49
- Working with Terminal 52
- Web Browser Requirements 54
- Overview of Menu Operations 56
- Figure 3-5. Monitoring 57
- 3.5 Turning IPmux-11 Off 58
- 4.1 Configuration Sequence 59
- Configuring DHCP Client 60
- Defining Network Managers 63
- Configuration Example 65
- Configuring User Access 66
- Configuring the System Clock 69
- 4.4 Additional Tasks 85
- Resetting IPmux-11 90
- 5.1 Overview 93
- 6.1 Monitoring Performance 99
- IPmux-11 Ver. 2.00 100
- Table 6-1. E1/T1 Statistics 101
- Displaying LAN Statistics 103
- 6.2 Detecting Errors 108
- Displaying Events 109
- Table 6-3. Event List 111
- Clearing Events 112
- 6.3 Handling Alarms 113
- 6.4 Troubleshooting 114
- 6.5 Testing IPmux-11 115
- Running External Loopback 115
- Running Internal Loopback 115
- Running a Trace Route 119
- 6.7 Technical Support 123
- A.1 E1 and T1 Connector 125
- A.2 Ethernet Connectors 126
- A.3 CONTROL Connector 126
- A.4 External Clock Connector 127
- B.1 Booting IPmux-11 129
- Software 130
- C.1 SNMP Environment 133
- MIB Structure 134
- SNMP Communities 136
- Authentication 136
- Network Management Stations 136
- Supplement 141
- Customer Response Form 143
- Error Report 145
Manuais e produtos relacionados com Gateways/controladores RAD Data comm IPmux-11
(108 páginas)Yamaha Acústica manuales de usuario
Empezando en N
Comentários a estes Manuais